![easyweather linux easyweather linux](https://lintut.com/wp-content/uploads/2020/03/Meteo-Weather-App.png)
- Easyweather linux install#
- Easyweather linux driver#
- Easyweather linux android#
- Easyweather linux series#
Easyweather linux install#
I’ve taken them and modified them to get working with raspian so there are a few minor changes.įirst we need to install some dependencies: ~ $ sudo apt-get install git ~ $ sudo apt-get install gnuplot python-simplejson python-tweepy python-paramiko Those instructions are for the Debian based image. Now this is based on the instructions over on .uk who got a Raspberry PI working with one of these weather stations. At the same time I enabled the ssh server from that same menu. With raspian this is easy as you get prompted on the first boot to do it. Booted the pi up and configured it to use the entire card. Configuring the Raspberry PIįirst I started with a blank copy of raspian on a 4Gb SD Card. All that’s needed is a USB A-A cable to connect the touch screen to the PI. It consists of the external sensors and an internal touch screen unit. The external components of the Weather Station At the time of writing this they’ve got it reduced to £69. They usually sell for about £125 but a couple of times a year they reduce them down to between £50-£70. The weather station that I’ve been using since November 2010 is one I bought from Maplin.
Easyweather linux series#
So this is the first part of a series on setting up a USB weather station onto a Raspberry PI. I think it’s power supply finally gave out after 9 years of service.
![easyweather linux easyweather linux](https://s.softdeluxe.com/screenshots/2837/2837213_7.jpg)
Unfortunately this project got pushed forward when, last Thursday morning, the ITX box decided to die on me. > USB port-only wifi.One of the reasons for having multiple PI’s was to have one take over duties from an aging ITX based Linux box of reading from a USB Weather station and uploading the data to both it’s website and WeatherUnderground. > I believe that it is a Fine Offset device but it doesn't seem to have a > Pretty new to weewx and I'm looking to replace my Accurite 5 in 1 with On Wednesday, Septemat 5:15:20 PM UTC-4 Hi, Back in terminal type: *sudo tail -f /var/log/syslog | grep Start “weewx:” *sudo /etc/init.d/weewx startġ1. Make sure “weewx” service is stopped: *sudo /etc/init.d/weewxġ0. Later I changed Upload interval to 30 seconds.ĩ. Ifconfig* in terminal on the computer where “weewx” is running. Modified “Customized” screen as shown in this image, exceptįor the ip address -should be the ip address of computer where On device, tapped “Next” in the upper right corner four times. When device appears in the device list of the “WS View” app tap Manual, page 33: “Connecting the Weather Station Console to Wi-Fi”ħ.
![easyweather linux easyweather linux](http://david.boxall.id.au/201808/images/20180628105918a.jpg)
Installed device select icon that looks like your TP3000WC,ĭisplay.
Easyweather linux android#
Installed Android app and install: WS View app for AndroidĦ. Note: iface may be different: *sudo ifconfig* look for your computerĥ. # wu-client - any hardware that uses the weather underground protocol # ecowitt-client - any hardware that uses the ecowitt protocol # lacrosse-bridge - lacrosse GW1000U/C84612 internet bridge # acurite-bridge - acurite internet bridge, smarthub, or access # Specify the hardware device to capture. # This section is for the network traffic interceptor driver. Next in section “” modify the following to match: Near the top of “nf ” change “debug = 0” to “debug = 1”
Easyweather linux driver#
Configured “Interceptor” driver in “nf:” *sudo nano *sudo wee_config -reconfigure -driver=user.interceptorĤ. Downloaded and installed “weewx” driver: Interceptor driverįollow driver install instructions stop after doing: Installed “weewx” using: Debian install instructionsģ. Downloaded and installed Linux Mint: Linux Mint DownloadĢ. TP3000WC, anemometer (wind speed cups) need to be on top of theġ. Firmware version can be found in the “WS View.” “Customized” Tycon Systems, TP3000WC and installing “weewx”ĮasyWeather firmware needs to be version 1.5.6 for this procedure to Yes, "weewx" can access the TP3000WC over wifi.